manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 23

Commissioning an inverter

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

23

3

The following Figure 3 1 shows which state changes are possible. The table below shows which conditions 

apply.

Fig. 3-1: Standard device state machine

Nicht Einschaltbereit

Einschaltsperre

Einschaltbereit

Eingeschaltet

Betrieb freigegeben

Schnellhalt aktiv

Störung

Störungsreaktion aktiv

0

2

1

3

4

5

6

9

7

8

11

12

14

13

15

16

10

Not ready for switchon

Fault reaction active

Fault

Quick stop active

Switchon disable

Ready for switchon

Switched on

Operation enabled

Change of state

Conditions

0

Device start-up 

 Not ready to switch on Control unit power supply turned on.

1

Not ready to switch on 

 switch on 

disable

Self test without errors and initialization completed.

2

Switch on disable 

 ready to switch on

•

Enable on low level (

E19

 bit 0 = 0 or 

A300

 = 0) or for 

initial start-up autostart active (

A34

)

•

DC link charged (

E03

)

•

Option ASP 5001 (Safe Torque Off) is not active (

E67

).

•

Axis activated (

E84

)

•

An IGB motion bus is not configured (configuration 

wizard, step 6, check box) or

•

No IGB motion bus is configured and either the IGB has 

reached the state 

3:IGB motion bus

 (

A155

) or IGB 

exception mode is activated (

A124

) or local mode is 

activated.

3

Ready to switch on 

 switched on

Enable on high level (

E19

 bit 0 = 1 and 

A300

 = 1).

4

Switched on 

 operation enabled

Enable on high level (

E19

 bit 0 = 1 and 

A300

 = 1).

5

Switched on 

 ready to switch on

Enable on low level (

E19

 bit 0 = 0 or 

A300

 = 0).

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands