Stober POSIDYN SDS 5000 Operation Manual Download Page 170

Page: 170 / 196

Diagnosis

Operation

manual

POSIDYN®

SDS

5000

ID 44

22
8

WE KEEP THINGS MOVING

11:SEA5001failure

SEA 5001 was detected, installed and

failed.

•

Uninstall the option, check the

contacts and reinstall the option.

•

Replace the option.

Switch the device on/off or

programmed acknowledgement

12:REA5001failure

REA 5001 was detected, installed and

failed.

•

Uninstall the option, check the

contacts and reinstall the option.

•

Replace the option.

Switch the device on/off or

programmed acknowledgement

13:PN5000 Failure1

PN 5000 was detected, installed and

failed. Basic hardware tests have

detected an error.

•

Check whether the PN 5000

accessory was correctly installed.

•

Check whether suitable EMC

measures were taken.

•

Check whether only PROFINET-

certified components were

connected to the inverter.

•

Check whether the cabeling and

connections correspond to the

PROFINET standard.

•

Contact the service department,

see section 1.4 Further support.

Switch device off/on

14:PN5000 failure2

PN 5000 was detected, installed and

failed. Basic software tests have

detected an error.

Switch device off/on

15:PN5000 failure3

PN 5000 was detected, installed and

failed. The watchdog function of the PN-

5000 monitoring system has detected

an error.

Switch device off/on

17:opt.2 too old

Option board with old hardware version

(XEA5001 HW 9, REA 5000 HW 18).

•

Install the latest version of the

option.

Switch device off/on

Cause

Description

Measure

Acknowledgement

Summary of Contents for POSIDYN SDS 5000





































































































































































































Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands

Stober POSIDYN SDS 5000, Operation Manual

Search results

Summary of Contents for POSIDYN SDS 5000

Reviews:

Brands by name

Popular brands