manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 116

Integrated Bus

ID 442289.06

116

Operation manual POSIDYN® SDS 5000

11

WE 

KEEP 

THINGS 

MOVING

There is a wide variety of causes for these errors. First, start the inverter again and check the network settings 

of the inverter and the company network. If this does not correct the error, contact STÖBER 

ANTRIEBSTECHNIK GmbH & Co. KG, see chapter 1.4 Further support

The following errors can occur in error category 03 

hex

:

This error may be caused because the HTTP response of the Teleserver is not reaching the inverter. Check 

the connection and the network settings. Receipt may also be blocked by a firewall. Check the firewall's 

settings, too.

Since general causes cannot be given for error categories 04 

hex

 and 05 

hex

, these errors were given a cause 

number. A description of the causes follows the description of the errors in category 05 

hex

.

0B

hex

Internal access was denied.

0C

hex

Internal access was denied.

0D

hex

Internal access was denied.

0E

hex

An error occurred while sending data.

0F

hex

An error occurred while sending data.

10

hex

An error occurred while receiving data.

11

hex

An error occurred while receiving data.

12

hex

An unknown HTTP status code was determined.

13

hex

An error occurred while remote maintenance was being exited.

Error value

Description

00

hex

Reserviert

01

hex

Es kam zu einem Timeout: Der Teleserver antwortete nicht.

02

hex

Der HTTP-Status-Code meldet einen HTTP-Fehler.

Error value

Description

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands