manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 131

Service

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

131

12

12.4.2

Replacing the firmware

WARNING!

Danger of personal injury or material damage due to unsecured loads. The firmware must be activated 
after the download for a live firmware update. The control part and power stage of the inverter are 
switched off during activation. Unsecured loads on the drive can therefore slip.

Secure the drive load before activation.

During a live firmware update the firmware is loaded to the firmware download memory without affecting 

running operation. The firmware does not become active until it is accepted. The firmware stored in the 

firmware download memory is kept as redundant firmware to increase safety.

Requirements:

•

The inverter controller is powered as a minimum (24 V at terminal X11). The power may only be switched 

off during download if the software gives an appropriate instruction. You can also carry out the live 

firmware update during ongoing operation.

•

You have connected a PC to the SDS 5000 or an IGB network.

•

You have configured at least one IGB network in POSITool.

You need:

•

POSITool version 5.4 or higher

Carrying out a live firmware update

1. In POSITool, open the 

IGB: display connected devices

menu entry in the File menu.

You will see the following dialog screen that displays all devices connected to the PC:

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands