manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 101

Integrated Bus

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

101

11

11.4.5

Settings for a LAN connection

To be able to establish a connection via the local network, the LAN Teleserver must be installed on a computer 

which is connected with the local network. Proceed as shown below:

The FQDN is the full computer name of a PC (i.e., Fully Qualified Domain Name). Remember that, when 

setting up a LAN connection, you must specify on the inverter (see Figure 11 16) and in POSITool, the FQDN 

of the computer on which the LAN Teleserver is installed.

Also note that the LAN teleserver should be installed on a high performance computer with a high level of 

availability.

Operating the LAN Teleserver

1. Start the POSITool-Teleserver.exe file on the computer on which the LAN Teleserver is to be installed.

The following dialog screen appears:

2. Make a note of the FQDN (Fully Qualified Domain Name).

You are now running the Teleserver on the local network.

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands