manualshive.com logo in svg

Stober POSIDYN SDS 5000, Operation Manual

Share
Download
Stober POSIDYN SDS 5000 Operation Manual Download Page 97

Integrated Bus

Operation manual POSIDYN® SDS 5000

ID 442289.06

WE 

KEEP 

THINGS 

MOVING

97

11

In the top part of this dialog screen, select the network connection of your PC which is connected to the same 

network as the inverter, and the related IP address, subnet mask and the IP addresses of the standard 

gateway and the DNS server appear in the bottom part of this screen. Confirm the dialog screen with the 

OK

 

button, and the IP addresses of the standard gateway and the DNS server are used. One position of the IP 

address of the PC is changed so that the IP addresses of the inverter and the PC are not the same. 

Remember that no check is made to determine whether the thus determined IP address is being used by 

another device in the network:

Fig. 11-13: The IP address determined from the network adapter

Note that, although you are only using the above settings for the gateway socket, the settings for the second 

socket in the dialog screen remain accessible. This means that you can enter an IP address for a direct 

connection for the second socket.

You can enter the IP address of the standard gateway in the lower part of the 

Network settings

 dialog screen. 

This is necessary for an Internet connection when there is DNS server in the network but a proxy server is not 

used.

Manual entry of the IP address of the DNS server is necessary if there is a DNS server in the network but its 

IP address is not transmitted by the DHCP server.

11.4.2.2

The Activation remote service tab

For example, you can specify the signal with which remote maintenance is to be activated under the 

Activation 

remote service

 tab. Select the gateway inverter from the list and double-click the line. The Set 

activation 

remote service

 dialog screen appears:

Fig. 11-14: The Set 

activation remote service

 dialog screen

Summary of Contents for POSIDYN SDS 5000





































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands