SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 86

Page: 86 / 100

Fault list – safety technology

Fault 68 Safe communication profile

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 68.10

Description: Configuration and application of fieldbus slave not plausible

Fault class: Warning

Cause

Measure

Transferred configuration of fieldbus slave does
not match application of fieldbus slave.

Make sure that the parameter setting for the field-
bus slave is plausible with the fieldbus slave in
use.

Subfault: 68.164

Description: Different addresses for PROFIsafe communication (F_Dest_Add)

Fault class: Message

Cause

Measure

Different addresses for PROFIsafe communica-
tion (F_Dest_Add) in fieldbus master and fieldbus
slave.

Set the same address for PROFIsafe communi-
cation (F_Dest_Add) in the fieldbus master and
fieldbus slave.

Subfault: 68.165

Description: Invalid address for PROFIsafe communication (F_Dest_Add)

Fault class: Message

Cause

Measure

Invalid PROFIsafe communication address
(F_Dest_Add).

Set a valid address for PROFIsafe communica-
tion (F_Dest_Add).

Subfault: 68.166

Description: Invalid failsafe source address (F_Source_Add)

Fault class: Message

Cause

Measure

Failsafe source address (F_Source_Add) not
valid or different failsafe source addresses detect-
ed in fieldbus master and fieldbus slave.

– Set a valid failsafe source address
(F_Source_Add).

– Set the same failsafe source address in the
fieldbus master and fieldbus slave.

Subfault: 68.167

Description: Invalid watchdog time for PROFIsafe communication

Fault class: Message

Cause

Measure

Watchdog time for PROFIsafe communication
(F_WD_Time, F_WD_Time_2) is 0 ms.

Set a valid watchdog time for PROFIsafe commu-
nication (F_WD_Time, F_WD_Time_2) in the
fieldbus master.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands