SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 78

Page: 78 / 100

Fault list – safety technology

Fault 67 Safe communication

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 66.173

Description: Referencing data accepted from safety key

Response: FS – message

Cause

Measure

Safety key accepted as the sole data source.

For information only.

Subfault: 66.174

Description: Direct referencing finished

Response: FS – log

Cause

Measure

Direct referencing finished.

For information only.

Subfault: 66.175

Description: Validation withdrawn

Response: FS – log

Cause

Measure

Validation has been withdrawn.

For information only.

2.16

Fault 67 Safe communication

Subfault: 67.10

Description: SafeCom control byte

Fault class: Warning

Cause

Measure

Error detected in the communication network of
SEW‑EURODRIVE. Safe communication nodes
not configured correctly.

– Make sure that the same safety protocol has
been set in fieldbus master and fieldbus slave.

– Make sure that the communication channel
between fieldbus master and fieldbus slave has
been configured correctly.

Subfault: 67.20

Description: Safety protocol system error

Fault class: System error

Cause

Measure

Safety protocol signaled system error.

– Acknowledge the fault.

– Restart safe communication.

– If the fault occurs again, switch the device off
and on again.

– If the fault occurs repeatedly, contact
SEW‑ EURODRIVE Service.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands