SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 94

Page: 94 / 100

Fault list – safety technology

Fault 70 Safe brake system

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 70.23

Description: Safe brake test aborted. Error, measured values.

Fault class: Warning

Cause

Measure

Failed to determine test torque while safe brake
test is running.

– Extend the duration of the individual test steps.

– If the fault occurs repeatedly, replace the device
and send it together with the fault number to
SEW‑EURODRIVE. For further support, contact
SEW‑EURODRIVE Service.

Subfault: 70.24

Description: Inverter firmware outdated

Response: FS – warning

Cause

Measure

Test ramps are not supported until inverter firm-
ware V6.

– Set the duration of the test ramps to 0.

– Perform a firmware update.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands