SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 56

Page: 56 / 100

Fault list – safety technology

Fault 63 Speed-dependent drive safety function

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 63.33

Description: SSx maximum speed exceeded in positive direction of movement

Fault class: Warning

Cause

Measure

SSx maximum speed exceeded in positive direc-
tion of movement during monitoring delay.

– Check the maximum speed of the application
while the drive safety function is active, and ad-
just if necessary.

– Check the parameter setting of the safety card
(maximum speed), and adjust if necessary.

Subfault: 63.41

Description: SSx maximum speed exceeded in negative direction of movement

Fault class: Warning

Cause

Measure

SSx maximum speed exceeded in negative direc-
tion of movement during monitoring delay.

– Check the maximum speed of the application
while the drive safety function is active, and ad-
just if necessary.

– Check the parameter setting of the safety card
(maximum speed), and adjust if necessary.

Subfault: 63.49

Description: SSx 1 limit speed exceeded in positive direction of movement during deceleration

Fault class: Warning

Cause

Measure

SSx 1 limit speed exceeded in positive direction
of movement during deceleration.

– Check deceleration, jerk time, and ramp type of
the application while the drive safety function is
active, and adjust if necessary.

– Check the parameter setting of the safety card
(deceleration SSx 1, jerk time SSx 1, ramp type
SSx 1), and adjust if necessary.

Subfault: 63.50

Description: SSx 2 limit speed exceeded in positive direction of movement during deceleration

Fault class: Warning

Cause

Measure

SSx 2 limit speed exceeded in positive direction
of movement during deceleration.

– Check deceleration, jerk time, and ramp type of
the application while the drive safety function is
active, and adjust if necessary.

– Check the parameter setting of the safety card
(deceleration SSx 2, jerk time SSx 2, ramp type
SSx 2), and adjust if necessary.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands