SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 44

Page: 44 / 100

Fault list – safety technology

Fault 61 Safe digital output

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 61.32

Description: F-DO 01 Crossfault

Fault class: Output fault

Cause

Measure

Crossfault in external wiring of safe digital output
F‑DO 01. Excessive capacitive load or test dura-
tion too short.

– Check the external wiring of safe digital output
F‑DO 01 for crossfault.

– Check the parameter "Maximum test duration".
If the maximum response time allows for a longer
test duration, set this parameter to a greater
value.

– Make sure that the capacitance of the connect-
ed load does not exceed the value permitted for
the output.

Subfault: 61.41

Description: F-DO 00_P Overcurrent

Fault class: Output fault

Cause

Measure

Permitted output current exceeded at P output of
safe digital output F-DO 00.

– Make sure that the current consumption of the
connected load does not exceed the permitted
output current. If necessary, change the load.

– Check the external wiring of safe digital output
F‑DO 00 for crossfault.

Subfault: 61.42

Description: F-DO 01_P Overcurrent

Fault class: Output fault

Cause

Measure

Permitted output current exceeded at P output of
safe digital output F-DO 01.

– Make sure that the current consumption of the
connected load does not exceed the permitted
output current. If necessary, change the load.

– Check the external wiring of safe digital output
F‑DO 01 for crossfault.

Subfault: 61.51

Description: F-DO 00_M Overcurrent

Fault class: Output fault

Cause

Measure

Permitted output current exceeded at M output of
safe digital output F-DO 00.

– Make sure that the current consumption of the
connected load does not exceed the permitted
output current. If necessary, change the load.

– Check the external wiring of safe digital output
F‑DO 00 for crossfault.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands