SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 10

Page: 10 / 100

Fault list – safety technology

Fault 13 Encoder 1

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 13.60

Description: Travel limit exceeded

Response: FS – encoder fault

Cause

Measure

Travel limit violated for an application with limited
travel distance.

– Check the startup parameters.

– Check the application.

– Perform referencing again.

Subfault: 13.61

Description: Wrong number of bits per telegram

Response: FS – warning

Cause

Measure

The number of bits received per telegram does
not match the number of parameterized bits.

– Check the startup parameters.

– Check the wiring.

– Check interference sources.

Subfault: 13.62

Description: Wrong cycle frequency

Response: FS – warning

Cause

Measure

Measured clock does not correspond with param-
eterized clock.

– Check the startup parameters.

– Check the wiring.

– Check interference sources.

Subfault: 13.64

Description: Inconsistent or corrupt data

Response: FS – warning

Cause

Measure

Inconsistent or corrupt data detected during en-
coder evaluation.

– Check interference sources (e.g. from the area
of EMC).

– Check the encoder cable or shield.

– Check the startup parameters.

Subfault: 13.65

Description: Illumination color error

Response: FS – warning

Cause

Measure

The lighting color in the encoder data does not
match the lighting color in use.

– Switch the device off and on again.

– If the fault occurs repeatedly, replace the en-
coder and send it to SEW‑EURODRIVE together
with the fault number. For further support, contact
SEW‑EURODRIVE Service.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands