SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 71

Page: 71 / 100

Fault list – safety technology

Fault 66 Safety-related fault

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 66.54

Description: Wrong version of the basic unit for limitation by the safety card

Response: FS – warning

Cause

Measure

Only basic units from version 4 support using the
limiting function.

Disable limiting or update the basic unit.

Subfault: 66.55

Description: Wrong version of the basic unit for configurable ramp times for the brake test

Response: FS – warning

Cause

Measure

Only basic units from version 6 support using
configurable ramp times in the brake test.

Set the ramp duration to 0 or update the basic
unit.

Subfault: 66.71

Description: SREF direct referencing – permitted movement exceeded

Response: FS – warning

Cause

Measure

During SREF direct referencing, the movement
must not be greater than the configured position
hysteresis.

– Check the application for standstill. If neces-
sary, adjust the controller.

– Check the parameter setting of the safety card
(position hysteresis) and adjust if necessary.

Subfault: 66.72

Description: SREF reference travel – reference switch left in wrong direction

Response: FS – warning

Cause

Measure

Reference switch left in the wrong direction dur-
ing SREF reference travel.

– Check the direction of rotation of the motor
when reference travel is active and correct if nec-
essary.

– Check the parameter setting of the safety card
(direction of movement of reference travel) and
adjust if necessary.

Subfault: 66.73

Description: SREF reference travel – maximum speed exceeded

Response: FS – warning

Cause

Measure

Maximum speed exceeded during SREF refer-
ence travel.

– Check the maximum speed of the application
while reference travel is active and adjust if nec-
essary.

– Check the parameter setting of the safety card
(maximum speed of reference travel) and adjust if
necessary.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands