SEW-Eurodrive MOVI-C MOVISAFE CS A Series Manual Download Page 84

Page: 84 / 100

Fault list – safety technology

Fault 67 Safe communication

Manual – Fault Descriptions MOVISAFE

CS..A

Subfault: 67.155

Description: Error in safety validator connection establishment engine TUNID

Response: FS – message

Cause

Measure

Error checking target unique network identifier
(TUNID).

– Make sure that the IP address in the originator
and the target is identical.

– Make sure that the SNN in the originator and in
the target is identical.

Subfault: 67.156

Description: Error in safety validator connection establishment engine SCID

Response: FS – message

Cause

Measure

Error checking safety configuration identifier
(SCID).

Check the configuration of the following SCID val-
ues:

– Combination of the values of the safety configu-
ration CRC (SCCRC) and the safety configuration

– Timestamp (SCTS)

Subfault: 67.157

Description: Error in safety validator connection establishment engine EKEY

Response: FS – message

Cause

Measure

Error in the electronic key.

Check the configuration of the target electronic
key in the engineering tool of the controller.

Subfault: 67.158

Description: Error in safety validator server client object timeout

Response: FS – message

Cause

Measure

Safety protocol signaled timeout.

– Make sure that the communication path was not
interrupted (cables, voltages, load).

– Make sure that the communication channel
between originator and target has been con-
figured correctly.

– Make sure that the monitoring times set in the
originator are not too low.

27799182/EN – 10/2022

Summary of Contents for MOVI-C MOVISAFE CS A Series





































































































Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands

SEW-Eurodrive MOVI-C MOVISAFE CS A Series, Manual

Search results

Summary of Contents for MOVI-C MOVISAFE CS A Series

Reviews:

Related manuals for MOVI-C MOVISAFE CS A Series

Brands by name

Popular brands