manualshive.com logo in svg

NEC Express5800/320Fd-MR, User Manual


Share
Download
background image

Installing and Using Utilities  5-105 

Title Bar 

The title bar displays the name of the current page of the Active Upgrade Console. 

The title bar also contains a Help button (

), which you can click to display the Help topic 

associated with the current page of the Active Upgrade Console. 

(You can also access the Help from the Production Side or Upgrade Side by clicking 

Start

, 

All 

Programs

, 

ftSys

, and 

Active Upgrade Help

 to open the Help viewer.) 

 

TIPS: 

Starting and Exiting the Active Upgrade Console, page 5- 
Understanding the Active Upgrade Console Interface, page 5-104 
Pre-Upgrade Tasks, page 5-96 
Configuring the Active Upgrade Process, page 5- 110 
 

Navigation Bar 

The navigation bar displays your current location in the Active Upgrade Console. 

If you are creating or editing a configuration file, the navigation bar also allows you to skip between 
configuration pages by clicking any item under the 

Configuration

 heading (see the figure below), 

or by clicking 

Active Upgrade

 to start a readiness check. 

Navigation Bar: Opening a Configuration Page 

 

After you initiate an upgrade (by clicking 

Split

 on the 

Active Upgrade

 page), the navigation bar 

reverts to a static mode, in which it only indicates where you are in the upgrade process and does 
not allow you to skip between pages. You must follow the upgrade steps (split, merge, commit, and 
finish) in order to complete the upgrade process, or you can abort the process altogether. 

Summary of Contents for Express5800/320Fd-MR





































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/320Fd-MR

Rack Solutions 122-2447 Installation Instructions Manual preview
122-2447
Brand: Rack Solutions Pages: 8
Quantum Snap! Server 4000 Quick Start Manual preview
Snap! Server 4000
Brand: Quantum Pages: 8
HMS Networks Anybus Communicator ABC4018 User Manual preview
Anybus Communicator ABC4018
Brand: HMS Networks Pages: 64
IBM 9009-41G Manual preview
9009-41G
Brand: IBM Pages: 36
TRENDnet TS-U100 - NAS Server - USB User Manual preview
TS-U100 - NAS Server - USB
Brand: TRENDnet Pages: 47
IBM x3350 - System - 4192 User Manual preview
x3350 - System - 4192
Brand: IBM Pages: 98
IBM x3500 - System - 7977 Installation Manual preview
x3500 - System - 7977
Brand: IBM Pages: 124
IBM System x3250 Installation And User Manual preview
System x3250
Brand: IBM Pages: 106
IBM x3200 - System M3 - 7328 Installation Manual preview
x3200 - System M3 - 7328
Brand: IBM Pages: 100
IBM System x3400 Type 7975 Installation Manual preview
System x3400 Type 7975
Brand: IBM Pages: 124
IBM System x3300 M4 Installation And Service Manual preview
System x3300 M4
Brand: IBM Pages: 470
IBM System x iDataPlex dx360 Manual preview
System x iDataPlex dx360
Brand: IBM Pages: 26
IBM System x3550 M3 Installation And User Manual preview
System x3550 M3
Brand: IBM Pages: 160
IBM System x3650 M4 Type 7915 Installation And User Manual preview
System x3650 M4 Type 7915
Brand: IBM Pages: 192
IBM x3750 M4 Installation And Service Manual preview
x3750 M4
Brand: IBM Pages: 694
IBM System x3755 M3 7164 Installation And User Manual preview
System x3755 M3 7164
Brand: IBM Pages: 126
ABB doGATE Installation Instructions Manual preview
doGATE
Brand: ABB Pages: 9
ABB SPA OPC User Manual preview
SPA OPC
Brand: ABB Pages: 68

Brands by name

Popular brands

Load more brands