manualshive.com logo in svg

NEC Express5800/320Fd-MR, User Manual


Share
Download
background image

5-10  Installing and Using Utilities 

If you select “Create a new partition” at “Windows system drive settings,” the 
contents of the hard disk will be all deleted. 

If “Use existing partitions” is selected, EXPRESSBUILDER install the Operating 
System to the 1st

 

partition (1st partition is deleted). The data in the other partition is 

kept if the system has two or more partitions. (See the figure below. 

 

 

 

You can not re-install the system with the existing partition that is upgraded to 
Dynamic Disk remained. Do not select “Use existing partitions” at “Windows system 
drive settings.” 

 

 

9. 

Enter the user information and client license mode. 

[Enter basic parameters] steps are displayed. Verify the parameters, modify if necessary, 
and then click [Next]. 

 

NOTE:

   

 

You must enter the computer name and the user name. 
 

10. 

Enter the setting of the network protocol. 

[Enter network protocol] steps are displayed. Retain the default value, and click [Next]. 

Summary of Contents for Express5800/320Fd-MR





































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for Express5800/320Fd-MR

Sun Microsystems Sun Fire X2100 M2 Service Manual preview
Sun Fire X2100 M2
Brand: Sun Microsystems Pages: 128
IBM 88861TU Installation And User Manual preview
88861TU
Brand: IBM Pages: 82
Edimax EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0 User Manual preview
EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0
Brand: Edimax Pages: 118
CNET CNP-101UW Specifications preview
CNP-101UW
Brand: CNET Pages: 2
xFusion Digital Technologies FusionServer G8600 V7 Manual preview
FusionServer G8600 V7
Brand: xFusion Digital Technologies Pages: 112
Sun Microsystems Sun Fire X4250 Volume Configuration Manual preview
Sun Fire X4250
Brand: Sun Microsystems Pages: 12
Supermicro SuperServer 7089P-TR4T User Manual preview
SuperServer 7089P-TR4T
Brand: Supermicro Pages: 155
LOVATO ELECTRIC DME Series Manual preview
DME Series
Brand: LOVATO ELECTRIC Pages: 5
Supermicro SuperServer 2029BT-HNC0R User Manual preview
SuperServer 2029BT-HNC0R
Brand: Supermicro Pages: 148
BITMAIN AntMiner S9 Repair Manual preview
AntMiner S9
Brand: BITMAIN Pages: 20
HP Windows Server 2008 R2 Administrator'S Manual preview
Windows Server 2008 R2
Brand: HP Pages: 18
HP TruCluster Server V5.1B-1 Specification preview
TruCluster Server V5.1B-1
Brand: HP Pages: 19
HP VT5900-H Quick Setup Manual preview
VT5900-H
Brand: HP Pages: 24
HP Virtual Connect FlexFabric-20/40 F8 Module Quickspecs preview
Virtual Connect FlexFabric-20/40 F8 Module
Brand: HP Pages: 23
HP ProLiant SL335s G7 Installation Sheet preview
ProLiant SL335s G7
Brand: HP Pages: 2
HP t820 Reference Manual preview
t820
Brand: HP Pages: 36
HP ProLiant SL2500 Gen8 Datasheet preview
ProLiant SL2500 Gen8
Brand: HP Pages: 4
HP ProLiant Plus Brochure preview
ProLiant Plus
Brand: HP Pages: 11

Brands by name

Popular brands

Load more brands