background image

System Configuration  4-21 

The table below lists how selections for “AC LINK” determine the power status of the server when 
the power supply to the server restarts. 

Parameter 

State before powered off 

Stay Off 

Last State 

Power On 

In 

service 

Off On On 

Out of service (DC power: Off) 

Off 

Off 

On 

Forced 

shutdown 

Off Off On 

*  Pressing the POWER switch for over four seconds shuts down the power to the server. 

 

 

System Management

 

Select “System Management” on the Server menu and press 

Enter

 to display the following screen. 

〈Example〉

 

 

See the table below for setup options on the screen. 

Option Parameter 

Description 

BIOS Version 

 

Displays the BIOS version.   

Board Part Number 

 

Displays the board information.   

Board Serial Number 

 

Displays the board information. 

System Part Number 

 

Displays the system information.   

System Serial Number 

 

Displays the system information. 

Chassis Part Number 

 

Displays the chassis information.   

   Main     Advanced     Security    

 Server 

    Boot     Exit    

ftServer Setup 

F1  Help   ↑↓ Select Item   -/+   Change Values       F9  Setup Defaults 
Esc Exit   ←→ Select Menu   Enter Select   Sub Menu   F10 Save and Exit 

System Management

 

Item Specific Help 

All items on this menu 
cannot be modified in 
user mode.  If any 
items require changes, 
please consult your 
system Supervisor. 

 

 

BIOS Version:      2.1:44 
 
Board Part #:      243-632791 
Board Serial #:    113108030768 
System Part #:     N8800-103 
System Serial #:   9072543618 
Chassis Part #:    243-535509 
Chassis Serial #:  01 
BMC Device ID:     26 
BMC Device Rev:    01 
BMC Firmware Rev:  0E.25 
SDR Rev:           SDR Version 00.10 
PIA Rev:           01.10 
ASIC Rev:          2023 
SMM Rev:           00.25 

 

Summary of Contents for Express5800/320Fd-MR





































































































































































































































































































































































































































































































Reviews: