Muratec mfx-2200, User Manual, Page: 366 / 382

10-4
5 Fax Settings 501 Default Settings
503 Fax Forward
You can set the default scanning resolution.
5011 Resolution
If you set this to ON, you can transmit faxes only
to another machine with the same passcode set.
Closed Tx page 6-2
If you set this to ON, you can receive faxes only
from another machine with the same passcode set.
Closed Rx
page 6-4
You can register a passcode required for the
closed transmission and reception.
Passcode
page 6-5
If you set this to ON, the lower four digits of
the fax number you dialed are compared with
those registered in the other machine, and
faxes will be transmitted only when the
numbers match.
ID check Tx
page 6-7
If you set this to ON, the screen for confirming the entered
destination number appears before starting transmission.
Check broadcast dest. page 6-10
If you set this to ON, the screen for re-entering the
fax number, which was entered using the numeric
keys, appears before starting transmission.
Dial double-push page 6-12
This allows documents received after the
security reception start time to be stored in
memory without being printed.
Security Rx page 6-14
You can set the default scanning contrast.
5013 Contrast
If you set this to ON, you can display or print a
TTI in the default setting.
5015 TTI
If you set this to ON, the memory transmission is
given priority in the default setting. If you set it to
OFF, the real time transmission is given priority.
5017 Memory Tx
If you select any of the documents 1 to 3, you
can always transmit the cover page attached to
the transmission document.
5019 Cover Page
If you set this to ON, you can automatically print
the transmission report at every transmission.
5021 Tx Report
If you set this to ON, you can always stamp
transmission documents.
5023 Stamp
You can set the default format of a file
attached to Internet Fax.
5025 File Format*1
You can set the default subject and message
attached to Internet Fax.
5027 Fixed Form*1
If you set this to ON, documents (faxes) received within a preset time can be forwarded to a
specified destination. You can also enter, change, or delete forwarding destinations information.
505 CoverPage Setup
You can register up to three cover page documents.
page 4-44
507 F-Code Box
You can register up to 20 F-code boxes for the F-code communication. You can
also delete the entered F-code box.
page 4-18
509 Security function
511 Other Settings
page 4-11
You can set the number of redial attempts that
will be carried out when the other line is busy.
5113 # Of Redials
You can set the redial interval.
5115 Redial Interval
You can block unnecessary fax reception. You
can register three modes to block faxes, and
also change or delete the registered contents.
5117 Block Junk Fax
When the reception mode is in fax mode or
tel/fax mode, you can set the number of rings
before fax reception starts.
5119 # Of Rings
You can set the default dialing pause when
you enter the pause symbol.
5121 Dialing Pause
You can set the default value for the Super
Fine (S-Fine) setting of the [Resol.] on the
touch panel display.
5123 High Resolution
You can set the print reduction rate for
received documents.
5125 Rx Reduc. Rate
When the received document will not fit in the
printing area, you can set values that
determine whether to cut off an edge or reduce
the contents to fit onto one sheet.
5127 Reduc. Margin
You can set the printing method for received
documents.
5129 Paper Saving
If you set this to ON, fax transmission for
multiple documents starts in the order of
pages that can be scanned and stored.
5135 Quick Memory Tx
If you set this to ON, any part of a document
that could not be transmitted correctly due to
a line error will be automatically resent.
5137 ECM Mode
You can put a number registered before a
destination number for dialing.
5141 Dial Prefix
You can select the address book type displayed
first on the fax standby screen.
5145 Default Address Book*1
You can collectively switch ON or OFF the
OfficeBridge received fax forwarding function.
5143 OB transmission setup*1
If you set this to ON, you can display the
Internet Fax-related keys (Mail) first on the
fax standby screen.
5147 Mail priority*1
When you divide the scanned multi-page
documents into one page for transmission
(divide transmission), you can set whether to
combine the transmission history in one
transmission or divide it per page.
5149 Divide Tx Setting*1
If you set this to ON, the received date and
time can be printed with the word “Received”
at the header of the received document.
5151 Recv.Time Stamp
Do not set.
5139 Service Mode
If you set this to ON, A4 documents can be
rotated to A4 for scanning and transmitted.
5133 Rotate Tx
page 8-15
page 6-1
page 8-17
DB2-90290-60.indb 4 2007/02/02 12:34:31