626
APPENDICES APPENDIX
Appendix 3 Compatible Devices with SSCNETIII(/H)
*1
Confirm the specifications of VC
series for details.
*2
The direct drive
DISC series manufactured by Nikki Denso Co., Ltd. can restore the absolute position in the range from -2147483648 to
2147483647. Confirm the specifications of VC
series for restrictions by the version of VC
series.
*3
When using the virtual encoder pulse number function of VC
series, the unlimited length feed is available. When this function is not
used, the unlimited length feed is not available. Confirm the specifications of VC
series for details of this function.
*4
The specification of torque limit direction differs by the version of VC
series. Confirm the specifications of VC
series for details.
*5
Refer to each servo amplifier instruction manual for the servo amplifiers that can be used.
Precautions during control
■
Absolute position system (ABS)/Incremental system (INC)
The setting of ABS/INC operates by the setting of VC
.
■
Unlimited length feed
When using the virtual encoder pulse number function of VC
series, the unlimited length feed is available. When this
function is not used, the servo error 61468 (F01CH) "Absolute encoder over flow error" occurs after "Encoder multiple
revolution counter
Encoder reso Encoder single revolution position" exceeds the range of -2147483648 to
2147483647, and the operation stops.
■
Home position return
When "1" is set in the first digit of the parameter of VC
series "Select function for SSCNET
on communicate mode", it is
possible to carry out the home position return without passing the zero point. (Return to origin after power is supplied will be
executed when passing of Motor Z phase is not necessary.) When "0" is set, the error "Home position return zero point not
passed" (error code: 197AH) occurs because the home position return is executed without passing the motor Z phase (Motor
reference position signal).
■
Control mode
Control modes that can be used are shown below.
• Position control mode (speed control including position control and position loop)
• Speed control mode (speed control not including position loop)
• Torque control mode (torque control)
However, it is not available to switch to continuous operation to torque control mode of expansion control "Speed-torque
control". If the mode is switched to continuous operation to torque control mode, the error "Continuous operation to torque
control not supported" (error code: 19E7H) occurs and the operation stops.
"1: Feedback torque" cannot be set in "Torque initial value selection (b4 to b7)" of "[Pr.90] Operation setting for speed-torque
control mode". If it is set, the warning "Torque initial value selection invalid" (warning code: 09E5H) occurs and the command
value immediately after switching is the same as the case of selecting "0: Command torque".
Amplifier-less operation
function
Possible (Operates artificially as one of the followings during amplifier-less operation.
• Servo amplifier type: MR-J4-10B, Motor type: HG-KR053 (resolution per servomotor rotation: 4194304 pulses)
• Servo amplifier type: MR-J3-10B, Motor type: HF-KP053 (resolution per servomotor rotation: 262144 pulses))
Servo parameter change
request
Possible (2 words write)
Possible (1 word write)
Driver communication
Not possible
Possible
Monitoring of servo parameter
error No.
Not possible
Possible
Servo alarm/warning
Alarm codes/warning codes detected
by VC
series are stored in "Servo
alarm/warning".
Alarm codes/warning codes detected by servo amplifier are stored in "Servo
alarm/warning".
Programming tool
MR Configurator2 is not available.
Use VC
data editing software.
MR Configurator2 is available.
Item
VC
series
*1
MR-J4(W)-B
MR-J3(W)-B
Summary of Contents for RD77MS16
