Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 451

Page: 451 / 468

Index

Inter-Tel

5000 Installation Manual – Issue 2.4, May 2008

Page

I-3

CAT 5/CAT 5e 4-10

CAT 5/CAT5e 4-20

CAT5e

See

Cables and Cabling

CF (Compact Flash) 5-107

Changing Protocol Modes

ITP and SIP 5-115

Channel Service Unit 4-25

as lighting protection 4-11

Channel Service Unit (CSU) 4-25

Chapter Overview 3-3, 4-4, 5-6, 6-2

Chapters of the Manual 2-3

Chassis Description 4-18

Check the Unit Pre-Assembly 5-14, 5-62

Checking the Unit Pre-Assembly 5-14, 5-62

CIR (Committed Information Rate) 4-54

Circuit Modules

installation 5-48

LSM-2 4-11

T1/E1/PRI 4-18, 4-25

Circuit Numbers

station 5-58

T1 4-27

trunks 4-29

Circuits

DTMF transmitter 4-19

T1 4-26, 4-27

Cisco® Configuration Command Examples B-22

Clear

network alarm A-28

Clearing Network Alarms A-28

Clock 4-19

CO Trunks 5-22, 5-26

CO Trunks in a European system 5-26

CO Trunks in a US system 5-26

Code-Accessible Endpoint Features 6-28

Committed Information Rate (CIR) 4-54

Communication Types B-5

Compact Flash (CF) 5-107

Compact flash memory card bay and Extractor Button 4-22

Compact Flash-Type Inter-Tel Memory Cards 6-4

Comparison of Inter-Tel Advanced Communications Platforms
B-21

Compatible UPS Units 4-7

Compatible USB Flash Drives 4-24

Compatible USB Hubs 4-7

Completed State 5-117, 5-118

Component Compatibility Matrix for 99 Nodes Support 4-58

Components of a Processor Module (PM-1) 5-37

Computer Telephony Integration (CTI) B-6

Conferencing

resources 4-19

resources on Processor Module (PM-1) 4-19

Configuration

network 5-7, A-6

Configuring Near-End NAT Traversal for IP Endpoints B-13

Configuring Near-End NAT Traversal for IP Gateway Trunks B-
17

Connecting

cables to a European System 5-80

cables to a US System 5-78

optional Off-Premises Extensions (OPX) 5-60

T1 and PRI trunks to the MDF 5-29

to the IPRC 5-119

trunk cables to the MDF 5-22

two T1/E1/PRI modules 5-32

Connecting Cables and Checking Cables to the System 5-67

Connecting CO Trunk Cables to the MDF 5-22

Connecting CO Trunks to a European System 5-26

Connecting CO Trunks to a U.S. System 5-26

Connecting DSS/BLF Units 5-192

Connecting Off-Premises Extensions 5-84

Connecting Optional Off-Premises Extensions (OPX) 5-60

Connecting PCDPM Cables 5-192

Connecting Station Cables to a European System 5-80

Connecting Station Cables to a U.S. System 5-78

Connecting Station Cables to the MDF 5-78

Connecting T1/PRI and E1/PRI Trunks to the MDF 5-29

Connecting T1M or T1M-2 Modules between Network Nodes 5-
32

Connecting to Model 8520 or 8560 Endpoints 5-198

Connecting Trunks to LSM-2 Module Ports 5-22

Connecting Trunks to LSM-4 Module Ports 5-24

Connecting Two T1M or T1M-2 Modules Together 5-32

Connection Interfaces for 8600 Series Multi-Protocol Endpoints
5-106

Connections to the Public Network 4-11

Connectors

PCM 4-23

Contact Information 6-2

Converting a Database from One Version to Another 5-89

CRAM-MD5 4-38

CS-5200 B-14

CS-5400 B-16

CSU

See

Channel Service Unit

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands