manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 385

Appendix A: Inter-Tel Private Networking

Sample Node Programming

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Page A-19

To prevent circular or excessive routes, the system limits the number of “hops.” A call or 
communication can take up to 10 hops to other nodes. However, 2-3 hops maximum is 
recommended. Using the example shown in Figure A-3 on 

page A-18

, Figure A-4 on 

page A-19

 

shows a call that makes three hops through intermediate nodes to reach a destination:

1. 

A call is placed from Node 1 to Node 4.

2. 

Node 1 attempts to route through Node Trunk Group 97502, but that route is not 
available. Node 1 then routes the call using Node Trunk Group 97501 and uses Nodes 2 
and 3 as intermediate nodes.

3. 

Because the network has already routed the call through Node 1, Node 2 will not use 
Node Trunk Group 97501 and routes the call through its Node Trunk Group 97502.

4. 

Node 3 routes the call through its Node Trunk Group 97502 to Node 4. It will not use 
97501 because the call came from Node 2.

Figure A-4. 

Example Call Path Through Nodes

Determining in what order to list the Node Trunk Groups in a Node and when to use Linear or 
Distributed search type depends on the system configuration and traffic. 

NODE 1

Trunk Grp 92001

Trunk Grp 92002

Node Trunk Grp 97501

Node Trunk Grp 97502

NODE 2

Trunk Grp 92010

Node Trunk Grp 97501

Node Trunk Grp 97502

NODE 4

Trunk Grp 92030

Node Trunk Grp 97501

Node Trunk Grp 97502

NODE 3

Trunk Grp 92020

Node Trunk Grp 97502

LOCAL

SERVICE

LOCAL

SERVICE

LOCAL

SERVICE

LONG DIST

SERVICE

LONG DIST

SERVICE

NOT AVAILABLE

Node Trunk Grp 97501

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands