manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 189

Chapter 5: Installation

Connecting Cables and Checking Cables to the System

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Page 5-67

Connecting Cables and Checking Cables to the System

At this point in the installation, all cabling to the MDF, patch panel, rack, and endpoints should 
be completed. This includes all cables that terminate at the chassis modules. 

To complete cabling:

1. 

Plug all applicable cables into their respective modules and chassis ports. 

2. 

Install the LAN cable from the Processor Module jack to a LAN connection. Plug the 
cable into a 100Base-T switch, instead of a hub. 

3. 

Connect the modules to MDF blocks or a patch panel using appropriate cabling. If 
replacing an Inter-Tel Axxess system, a 15 ft (4.5720 m) Amphenol-to-DEM-16 cable is 
available, part no. 813.1814.

See Figure 5-35 on 

page 5-68

 for a pinout and cabling example. Pinouts must follow the 

568B standard.

4. 

If installing optional equipment, see “Optional System Equipment” on 

page 5-169

 and 

following. 

5. 

Continue to “Grounding the Inter-Tel 5000 Base Server” on 

page 5-16

. 

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands