manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 31

Chapter 1: Inter-Tel 5000 v2.4 New Features

Administrative Web Session (AWS) Pages

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Page 1-7

Administrative Web Session (AWS) Pages

The Administrative Web Session (AWS) pages include a variety of changes for Inter-Tel 5000 
system software v2.4. Some changes include new pages and information for Mitel IP endpoints 
and for the Inter-Tel 5000 onboard trivial file transfer protocol (TFTP) server. 

See the Installation chapter for information on the AWS pages pertaining to upgrades (

page 5-

149

) and the onboard TFTP server (

page 5-147

). 

For additional details on changes to AWS, refer to the 

Inter-Tel 5000 Features and 

Programming Guide

 (580.8006).

System Upgrade Page

The System Upgrade page was named the System and Application Upgrade page. The System 
Upgrade page is now located under the System Management

 

navigation tab. The System 

Upgrade page allows you to download and upgrade system, application, and now endpoint 
software. 

You can now use the System Upgrade page to upgrade endpoint software by using the onboard 
TFTP server. This page was also enhanced to include Mitel IP endpoint software. See 
“Procedure: Upgrading the System to Version 2.4” on 

page 5-149

 for more details about using 

this page.

Figure 1-1. 

AWS System Upgrade Page

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands