Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 273

Page: 273 / 468

Chapter 5: Installation

Procedure: Upgrading the System to Version 2.4

Inter-Tel

5000 Installation Manual – Issue 2.4, May 2008

Page 5-151

In the navigation panel, click

Operations

, and then click

System Upgrade

. The

following screen appears.

Do the following:

TFTP Address

: Type the IP address of the TFTP server holding the v2.4 upgrade

files.

Make sure this IP address setting points to a separate TFTP server—not to the
onboard TFTP server on the Inter-Tel 5000.

b. Click

Change Location

10. Click

Update

at the bottom of the page to see a list of available packages and

applications. An example is shown on the next page.

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands