manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 308

Chapter 5: Installation
In Professional Display or Associate Display Endpoints

Page 5-186

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

In Professional Display or Associate Display Endpoints

To install a PCDPM in a Professional or Associate Display Endpoints: 

1. 

Press up on the tabs and lift off the cover. Remove the cover and the display endpoint 
foot in the back, as shown below.

2. 

Align the PC Data Port Module over the connector inside of the display endpoint and the 
three pins on the outside. Gently press the module into place until the connector is 
securely positioned into place, as shown below.

3. 

Attach the module to the display endpoint using the two mounting screws.

4. 

Plug the appropriate end of the PCDPM-to-MDPM interface cable, part no. 813.1566, 
into the MDPM connector (

J1

), shown above, on the module. The other end of the cable 

will later be attached to the MDPM after it is installed.

Pin 1 of the cable, indicated by the stripe on the edge of the cable, must correspond to 
pin 1 on the MDPM connector, indicated by the notch silk-screened on the module.

BACK OF DISPLAY ENDPOINT

DISPLAY ENDPOINT 

COVER

FOOT

BACK OF DISPLAY ENDPOINT

PCDPM

J2

J1

P1

P1

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands