manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 300

Chapter 5: Installation
Installing SIP Gateways

Page 5-178

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Caller ID receivers are not available on all SIP gateways. Consult the device documentation for 
information on Caller ID support. Refer to the 

Inter-Tel 5000 Features and Programming Guide 

(part no: 580.8006) for additional details. Figures 

5-66

 and 

5-67

 illustrate a remote site without 

or with an SIP gateway.

Figure 5-66. 

Example of a Remote Site without a SIP Gateway Application

Figure 5-67. 

Example of a Remote Site with a SIP Gateway Application

NOTICE

It is the responsibility of the organization and person(s) performing the installation and 
maintenance of Inter-Tel Advanced Communications Platforms to know and comply with all 
regulations required for ensuring Emergency Outgoing Access at the location of both the 
main system and any remote communication endpoints. Remote IP and SIP endpoints may 
require gateway access to nearby emergency responders. 

Emergency Call phone numbers include: 

•

911, the default for Inter-Tel systems located in the United States (USA).

•

999, the default for Inter-Tel systems located in the European market and used primarily 
in the United Kingdom (UK).

•

If applicable, 112, an emergency number used widely in Europe outside of the UK.

•

Any emergency number, such as for a police or fire station, that is appropriate for the 
location of the main system and/or remote endpoints.

IP Resource

Inter-Tel 5000

PSTN

IP NETWORK

IP Endpoint

911

Operator

Located in Orange, CA

Caller ID Display:

714-283-1600

480-961-9000

Located in Phoenix, AZ

480-961-9000

Remote Site

Caller dials 911

In Phoenix, AZ

System

IP Resource

Inter-Tel 5000

PSTN

IP NETWORK

IP Endpoint

911

Operator

Located in Orange, CA

Caller ID Display:

714-283-1600

714-283-1600

Located in Phoenix, AZ

480-961-9000

Remote Site

SIP

Gateway

(AudioCodes)

Caller dials 911

In Orange, CA

System

IMPORTANT

The SIP gateway is intended to connect to the PSTN. Connecting the SIP 
gateway to single line ports on other systems is 

not

 supported.

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands