Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 356

Page: 356 / 468

Chapter 6: Reference
SIP and ITP Default Feature Codes

Page 6-34

Inter-Tel

5000 Installation Manual – Issue 2.4, May 2008

Table 6-22

shows default codes when operating in ITP mode.

Table 6-22.

Inter-Tel Protocol IP Default Feature Codes

Feature

Code

Feature

Code

1. Account Code – Following Calls

391

Hunt Group Remove

322

Account Code – Optional

390

Hunt Group Replace

323

ACD Agent Log In

326

Hunt Group Remove/Replace

324

ACD Agent Log Out

327

LCD Contrast Control

303

ACD Agent Log In/Out

328

Message

365

ACD Agent Wrap-Up Terminate

329

Message – Cancel Message Left

366

Agent Help Request

375

Message – Cancel Message on
Phone

368

Agent Help Reject

376

Message – Silent Message

367

Answer (Ringing Call)

351

Microphone Mute On/Off

314

Automatic Intercom Access On/Off

361

Page

Automatic Line Access On/Off

360

Page Receive On/Off

325

Automatic Line Answer

350

Program Buttons

397

Background Music On/Off

313

Program Station Password

392

Call Forward All Calls

355

Queue (Callback) Request

Call Forward If Busy

357

Record-A-Call

385

Call Forward If No Answer

356

Redial

380

Call Forward No Answer/Busy

358

Redirect Call

331

Conference

Reminder Message

305

Default Station

394

Reminder Message Cancel

306

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands