manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 406

Appendix B: Network IP Topology
Private (Trusted) Networks

Page B-8

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008 

To allow IP endpoints on the Internet in the private networking scenario described above, you 
may want to consider the following options:

•

Configure a static NAT assignment in the near-end NAT. Program the CS-5200/5400/5600 
to know its NATed address along with which endpoints are connecting from the Internet. 
See “Configuring Near-End NAT Traversal for IP Endpoints” on 

page B-13

.

•

Provide VPN connectivity between the private network and the network containing the IP 
endpoint.

•

Network an additional Inter-Tel CS-5200/5400/5600 using PRI networking, and place it in a 
non-NATed DMZ as described in “Public (Untrusted) Networks” on 

page B-9

.

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands