manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 225

Chapter 5: Installation

Procedure

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Page 5-103

Procedure

To install IP endpoints, see the following sections:

•

8600-series endpoints (see below)

•

5000-series endpoints (

page 5-154

 as part of the upgrade procedure for this release)

To install 8600-series IP phones:

See the following illustrations for connection point examples:

•

Model 8660 (

page 5-105)

•

Models 8600, 8620/8622, and 8662 (

page 5-106)

•

Model 8690 (

page 5-107)

•

Axxess IP PhonePlus (

page 5-108)

•

Eclipse IP PhonePlus (

page 5-109)

1. 

Make sure the Inter-Tel 5000 system is up and running. Also, read “Notices” on 

page 5-

101

. 

2. 

Connect one end of the Ethernet cable to a PC port on the back of the endpoint. 
Connect the other end of the cable to the PC, if applicable. 

For the Model 8660, use unbooted Ethernet cables. The Model 8660 does not support 
booted cables because the plastic “protective” ends on booted Ethernet cables get in the 
way when routing the cable away from the endpoint.

3. 

Connect the power supply, using one of the following methods. Use CAT5 or better cable 
for all LAN jack/plug connections in this procedure.

Depending on the IP devices to be used, there are several power supplies available. For 
a list of power supply compatibilities for the supported IP endpoints and devices, see the 

IP Device Power Supply Compatibility Matrix

, part no. 835.2688.

 •

USA/European/Universal Power Supply using a LAN Jack

: 

a.)

Connect the LAN/POWER jack on the baseplate to the KS/SLA jack on the 
24 VDC adapter. 

b.)

Using another cable, connect the LAN jack on the 24 VDC adapter to the 
LAN. 

c.)

Connect the 24 VDC adapter to a 110 V wall socket. Inter-Tel currently offers 
the following power supply kits. 

Table 5-14. 

Power Supply Kits

Part Number

Contains

828.1642

•

U.S. power supply, part no. 806.1113

•

Network cable, part no. 813.1790

828.1660

•

Universal power supply, part no. 806.1119*

•

Network cable part no. 813.1790

 * Requires a standard IEC (International Electrical Cord) power connector. 

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands