manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 409

Appendix B: Network IP Topology

Public (Untrusted) Networks

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008 

Page B-11

For the Inter-Tel CS-5200/5400/5600 system and other IP devices to function properly in the 
DMZ, 

the DMZ must be a non-NAT network

. That is, the devices in the DMZ use 

public

 IP 

addresses. The firewall can still provide some protection from the public Internet, but it does not 
translate the IP addresses or port numbers. An example is shown in the following illustration.

 

Internet

LAN

Remote or home 

office Firewall/NAT

LAN

Non-NAT DMZ

Inter-Tel 5x00

Public IP Address(es)

DB Programming,

OAI Apps,

Diagnostics Monitor ,

System Monitor

Router/Firewall/NAT

Public 
Interface

Private NAT 
Interface

Non-NAT DMZ 
Interface

UC/SIP Server

Enterprise

Conferencing

IP Endpoint

IP Endpoint

IP Endpoint

IP Endpoint

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands