Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 230

Page: 230 / 468

Chapter 5: Installation
Axxess IP PhonePlus

Page 5-108

Inter-Tel

5000 Installation Manual – Issue 2.4, May 2008

•

LEDs

There are two indications on each port:

Link Status

When the link is valid, the green LED on the left side of the port is lit.

When there is receive or transmit activity on the link, this LED flashes.

10/100 Mbps

: When the link is connected at a speed of 100 Mbps, the green LED on

the right side of the port is lit. The Inter-Tel 5000 platform operates

only

on 100Base-T

LANs.

•

DRAM

: Located inside the endpoint. Supports 128 MB (only one slot is occupied).

Although there are two DRAM slots, you cannot upgrade the memory by adding an extra
memory stick. Currently, the second slot is not used.

For information about how to program a Model 8690, refer to the

Inter-Tel 5000 Features and

Programming Guide

(part no: 580.8006).

To use the Model 8690, you must first install the 8690 client application. refer to the

Inter-Tel

5000 Features and Programming Guide

(part no: 580.8006) for details.

Axxess IP PhonePlus

The drawing at right depicts the connection
interfaces on the bottom of the endpoint. The Axxess
IP PhonePlus provides the following connections:

•

LAN/POWER Jack

: Connects to an external

power supply and a network hub/switch.

•

POWER Jack

Connects to a 24 VDC external

power supply. Use only one power source to
connect the power supply.

•

OUT TO PC Jack

: Connects to a PC.

•

LEDs

: Two LEDs indicate activity on each port:

Link Status

When the link is valid, the green LED on the left side of the port lights.

When receive or transmit activity occurs on the link, the LED flashes.

Collision

: When both receive and transmit activities occur on the link at the same time,

the yellow LED on the right side of the port lights.

For information about programming an Axxess IP PhonePlus, refer to the Programming chapter
in the

Inter-Tel 5000 Features and Programming Guide

(part no: 580.8006).

LAN/POWER

To PC

Power

LEDs

Bottom

Supply

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Search results

Summary of Contents for Inter-Tel 5000

Reviews:

Brands by name

Popular brands