manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 332

Chapter 6: Reference
Analog Single Line Modules

Page 6-10

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

Analog Single Line Modules

Table 6-11

 identifies the single line modules available for equipping Inter-Tel 5000 platforms with 

analog single line endpoints. The four-port single line module (SLM-4) is installed in the Inter-Tel 
CS-5200/5400/5600 Base Server. A system can support only one SLM-4. The eight-port single 
line module (SLM-8) is installed in a DEI bay, and a system can support up to six SLM-8 
modules.

Batteries

Table 6-12

 identifies the batteries that can be replaced on the Inter-Tel 5000 platforms.

Table 6-11. 

Single Line Modules 

Description

Part No.

Four-port Single Line Module (SLM-4)

580.2100

Eight-port Single Line Module (SLM-8)

580.2101

Table 6-12. 

Batteries 

Description

Part No.

Database Back-Up Battery (3.6V, coin lithium-ion) 

815.1011

Rechargeable Battery (PM-1 Only) 

815.1026

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands