manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 380

Appendix A: Inter-Tel Private Networking
IP Resource Programming

Page A-14

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

8. 

Under System\Devices and Feature Codes\Node IP Connection Groups, enter a 
description and username for the each P8XXX extension. Use a description/username 
that identifies where the off-node extensions reside. For example, if P8000 includes the 
off-node IP connection extension for connecting to Node 2, use TO NODE 2 as the 
description/username for P8000.

9. Under 

System\Devices 

and Feature Codes\Nodes\97XXX\Node Trunk/IP Connection, 

add the Node IP Connection Group extension (P8XXX) to the appropriate node (for 
example, the remote node created in step 3 on 

page A-12

).

10. 

Repeat step 1 on 

page A-12

 through 

step 9

 for all nodes that will be networked through 

IP networking.

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands