manualshive.com logo in svg

Mitel Inter-Tel 5000, Installation And Maintenance Manual

Share
Download
Mitel Inter-Tel 5000 Installation And Maintenance Manual Download Page 310

Chapter 5: Installation
In Model 8520 or Model 8560 Endpoints

Page 5-188

Inter-Tel

® 

5000 Installation Manual – Issue 2.4, May 2008

7. 

Because a Modem Data Port Module will be attached to the PC Data Port Module,

 

see 

the instructions on 

page 5-190

. The only purpose of installing a PCDPM in a digital 

endpoint is to provide the copper path between the MDPM and a DSS/BLF unit. There is 
no need to install a PCDPM without also installing an MDPM.

Figure 5-71. 

PCDPM Installation in an Executive or Standard Display Endpoint

BACK OF DIGITAL ENDPOINT

INSIDE OF BASEPLATE

If the endpoint will be wall-mounted, open
the back of the endpoint and reroute the
Module-to-Keyset Interface cable through
this knockout over to connector J3 on the
control board. 

TO CHASSIS

J3

TO

HANDSET 

PCDPM

RS232

CONNECTOR

MDPM

CONNECTOR

To Modem Data

TO DSS/BLF UNIT OR

PC/OUTPUT DEVICE

J1

P1

Older PCDPMs, part no. 550.3014, require AC transformers when they are connected to DSS/BLF units only.
PCDPMs do not require AC transformers when they are used for off-hook voice announce only or have
attached MDPMs. For a diagram of AC transformer requirements, see Figure 5-70 on 

page 5-184

. Also, some

early PCDPM-to-MDPM cables may have the stripe on the wrong edge. If the MDPM does not respond prop-
erly, try reversing the connector on the PCDPM.

J2

Port Module

Summary of Contents for Inter-Tel 5000





















































































































































































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands