IBM P260 Installation And Service Manual Download Page 441

Page: 441 / 524

2D29-102E

Explanation:

Reallocation failed due to disk out of alternate sectors. Replace the FRU identified by diagnostics.

Response:

Failing Item:

FFC_722

2D29-3002

Explanation:

Addressed device failed to respond to selection. Replace the FRU identified by diagnostics.

Response:

Failing Item:

FFC_722

2D29-3010

Explanation:

Disk returned wrong response to adapter. Replace the FRU identified by diagnostics.

Response:

Failing Item:

FFC_722

2D29-3020

Explanation:

Storage subsystem configuration error. Use MAP3150 to determine resolution.

Response:

2D29-3100

Explanation:

Controller detected device bus interface error. Use MAP3150 to determine resolution.

Response:

2D29-3109

Explanation:

Controller timed out a device command. Use MAP3150 to determine resolution.

Response:

2D29-3110

Explanation:

Device bus interface error. Use MAP3150 to determine resolution.

Response:

2D29-102E • 2D29-3110

Chapter 8. Troubleshooting

429

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands