manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

B2D03001

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B2D03002

Explanation:

Informational system log entry only.

Response:

No corrective action is required.

B6xxyyyy licensed internal code or hardware event SRCs:

A B6xxyyyy system reference code (SRC) is an error code or event code that is related to licensed internal
code or hardware.

The B6xxyyyy SRCs below are the system reference codes that might be displayed if system firmware
detects a problem. Follow the suggested actions in the order in which they are listed until the problem is
solved. If an action solves the problem, then you can stop performing the remaining actions. See
Chapter 7, “Parts listing for IBM Flex System p260 and p460 Compute Nodes,” on page 97 to determine
which components are CRUs and which components are FRUs.

Note:

For problems persisting after completing the suggested actions, see “Solving undetermined

problems” on page 498.

A6000255

Explanation:

Contact was lost with the device indicated in the SRC. The operating system is halted waiting for the

I/O function of a critical resource to return. When the I/O returns this SRC will disappear from the panel and the
O/S will continue running. This problem occurs when the connection to the I/O resource or host is suspended, lost
or there is a problem with I/O in the host.

The O/S cannot notify or call home in this state.

Service action / serviceable event : YES

Called home automatically: Conditional from the management console.

v

If this LPAR was defined from the managent console with the option for calling home crashes and hangs then the
management console will call this problem home.

v

Otherwise this problem will not be called home.

Problem determination:

Do not power off the LPAR. Look for and repair problems in the I/O host.

A6000266

Explanation:

Contact was lost with the device indicated in the SRC. The operating system is halted waiting for the

I/O function of a critical resource to return. When the I/O returns this SRC will disappear from the panel and the
O/S will continue running. This problem occurs when the connection to the I/O resource or host is suspended, lost
or there is a problem with I/O in the host.

The O/S cannot notify or call home in this state.

This SRC will continue to be refreshed in the panel periodically in the third and fourth "XX" digits (A6XX0266 or
B6XX0266) while the O/S is in this state.

Service action / serviceable event : YES

Called home automatically: Conditional from the management console.

v

If this LPAR was defined from the managent console with the option for calling home crashes and hangs then the
management console will call this problem home.

v

Otherwise this problem will not be called home.

Problem determination:

Do not power off the LPAR. Look for and repair problems in the I/O host.

B2D03001 • A6000266

166

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Raymarine E-Series Reference Manual preview
E-Series
Brand: Raymarine Pages: 360
Raymarine E-Series User Reference Handbook preview
E-Series
Brand: Raymarine Pages: 260
NEC MD213MC - MultiSync - 21.3" LCD Monitor Installation And Maintenance Manual preview
MD213MC - MultiSync - 21.3" LCD Monitor
Brand: NEC Pages: 32
NEC MD205MG-1 - MultiSync - 20.1" LCD Monitor Specifications preview
MD205MG-1 - MultiSync - 20.1" LCD Monitor
Brand: NEC Pages: 2
NEC LCD52VM - AccuSync - 15" LCD Monitor Specifications preview
LCD52VM - AccuSync - 15" LCD Monitor
Brand: NEC Pages: 2
NEC LCD2690WUXI2 Specification preview
LCD2690WUXI2
Brand: NEC Pages: 2
NEC LCD2470WVX - MultiSync - 24" LCD Monitor Technical Specification preview
LCD2470WVX - MultiSync - 24" LCD Monitor
Brand: NEC Pages: 2
NEC LCD1880SX - MultiSync - 18.1" LCD Monitor User Manual preview
LCD1880SX - MultiSync - 18.1" LCD Monitor
Brand: NEC Pages: 40
NEC MultiSync EA224WMi Setup Manual preview
MultiSync EA224WMi
Brand: NEC Pages: 2
NEC MULTISYNC E201W User Manual preview
MULTISYNC E201W
Brand: NEC Pages: 21
NEC LCD52VM - AccuSync - 15" LCD Monitor User Manual preview
LCD52VM - AccuSync - 15" LCD Monitor
Brand: NEC Pages: 46
NEC AccuSync LCD72VX Brochure preview
AccuSync LCD72VX
Brand: NEC Pages: 2
NEC LCD19WMGX - AccuSync - 19" LCD Monitor Brochure & Specs preview
LCD19WMGX - AccuSync - 19" LCD Monitor
Brand: NEC Pages: 2
NEC LCD1990SXi BK MultiSync -LCD User Manual preview
LCD1990SXi BK MultiSync -LCD
Brand: NEC Pages: 29
NEC MultiSync 24WMGX3 Specification preview
MultiSync 24WMGX3
Brand: NEC Pages: 2
NEC LCD2190UXP - MultiSync - 21" LCD Monitor Specifications preview
LCD2190UXP - MultiSync - 21" LCD Monitor
Brand: NEC Pages: 2
NEC LCD2010 - MultiSync - 20.1" LCD Monitor User Manual preview
LCD2010 - MultiSync - 20.1" LCD Monitor
Brand: NEC Pages: 39
NEC MD242C2 Installation And Maintenance Manual preview
MD242C2
Brand: NEC Pages: 36

Brands by name

Popular brands

Load more brands