IBM P260 Installation And Service Manual Download Page 420

Page: 420 / 524

2E52-201

Explanation:

Adapter configuration error Replace the IBM Flex System CN4058 8-port 10Gb Converged Adapter If

the problem persists, replace the system board.

Response:

Failing Item:

FFC_2E52

FFC_221

2E52-605

Explanation:

Ethernet hardware error Replace the IBM Flex System CN4058 8-port 10Gb Converged Adapter

Response:

Failing Item:

FFC_2E52

2E52-606

Explanation:

Ethernet configuration error Replace the IBM Flex System CN4058 8-port 10Gb Converged Adapter

Response:

Failing Item:

FFC_2E52

2E52-607

Explanation:

EEH error Replace the IBM Flex System CN4058 8-port 10Gb Converged Adapter

Response:

Failing Item:

FFC_2E52

2E53-201

Explanation:

Adapter configuration error. Replace the PCIe2 10Gb 8-port FCoe Mezzanine Adapter If the problem

persists, replace the system board.

Response:

Failing Item:

FFC_2E53

FFC_221

2E52-201 • 2E53-201

408

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands