IBM P260 Installation And Service Manual Download Page 191

Page: 191 / 524

B7005603

Explanation:

Enclosure feature code and/or serial number not valid.

Response:

Verify that the machine type, model, and serial number are correct for this server.

B7006900

Explanation:

PCI host bridge failure

Response:

Replace the system-board, as described in Replacing the system-board and chassis assembly.

If the problem persists, use the PCI expansion card (PIOCARD) problem isolation procedure to determine the

failing component.

B7006906

Explanation:

System bus error

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006907

Explanation:

System bus error

Response:

Replace the system-board, as described in Replacing the system-board and chassis assembly.

Go to Isolating firmware problems.

B7006908

Explanation:

System bus error

Response:

Replace the system-board and chassis assembly, as described in Replacing the system-board and chassis

assembly.

B7006909

Explanation:

System bus error

Response:

Replace the system-board, as described in Replacing the system-board and chassis assembly.

Go to Isolating firmware problems.

B7005603 • B7006909

Chapter 8. Troubleshooting

179

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands