IBM P260 Installation And Service Manual Download Page 326

Page: 326 / 524

652-733

Explanation:

A non-critical error has been detected: intermediate or system bus address parity error. Schedule

deferred maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2C8

FFC_292

652-734

Explanation:

A non-critical error has been detected: intermediate or system bus data parity error. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2C8

FFC_292

652-735

Explanation:

A non-critical error has been detected: intermediate or system bus time-out error. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2D2

FFC_292

652-736

Explanation:

A non-critical error has been detected: intermediate or system bus time-out error. Schedule deferred

maintenance. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_2D2

FFC_292

652-733 • 652-736

314

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands