IBM P260 Installation And Service Manual Download Page 60 | Manualshive

Page: 60 / 524

background image

7.

If you are instructed to return the hard disk drive, follow all packaging instructions, and use any
packaging materials for shipping that are supplied to you.

Installing a SAS hard disk drive

If your serial-attached SCSI (SAS) hard disk drive needs replacing, install another SAS hard drive in the
compute node.

About this task

Figure 18 shows how to install the hard disk drive.

All drive connectors are from the same controller. Both the IBM Flex System p260 Compute Node and
IBM Flex System p460 Compute Node can be used to implement RAID functions. See “Configuring a
RAID array” on page 28 for information about RAID configuration.

To install a hard disk drive, complete the following steps:

Procedure

1.

Read the Safety topic and the “Installation guidelines” on page 35.

Figure 18. Installing a hard disk drive

48

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
58
59
60
61
62
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: Wacom Pages: 26

Brand: Haloview Pages: 18

Brand: Digital Equipment Pages: 76

Brand: YEYIAN Pages: 28

Brand: ViewSonic Pages: 115

PERFECTVIEW M75LX

Brand: Waeco Pages: 248

Brand: V-Tec Pages: 4

Brand: Mastervolt Pages: 33

Brand: Power View Pages: 3

Brand: Hisense Pages: 42

Brand: ViewSonic Pages: 2

Brand: Barco Pages: 54

Brand: ViewSonic Pages: 2

ColorEdge CG210

Brand: Eizo Pages: 73

BOOSTXL-K350QVG-S1

Brand: Texas Instruments Pages: 10

Brand: InMotion Pages: 17

Brand: Absen Pages: 52

Brand: Westinghouse Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands