manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

7.

Gently spread open the carrier with your fingers while sliding the SSD out of the carrier case with
your thumbs.

8.

If you are instructed to return the drive, follow all packaging instructions, and use any packaging
materials for shipping that are supplied to you.

Installing a SATA solid-state drive

You can install a Serial Advanced Technology Attachment (SATA) solid-state drive (SSD) in a compute
node.

About this task

Figure 22 shows how to install the SATA SSD.

To install a SATA SSD, complete the following steps:

Procedure

1.

Read the Safety topic and the “Installation guidelines” on page 35.

2.

Shut down the operating system on all partitions of the compute node, turn off the compute node,
and remove the compute node from the IBM Flex System Enterprise Chassis. See “Removing the
compute node from an IBM Flex System Enterprise Chassis” on page 37.

3.

Carefully lay the compute node on a flat, static-protective surface, with the cover side up.

4.

Open and remove the compute node cover. See “Removing the compute node cover” on page 39.

5.

Locate the connector for the drive.

6.

Remove the SSD carrier case from the drive tray. See “Removing a solid-state drive carrier” on page
49.

7.

Slide the SSD into the carrier case until it snaps in place.

Figure 22. Installing a SATA SSD

54

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Scosche RHYTHM+ User Manual preview
RHYTHM+
Brand: Scosche Pages: 24
ThinkVision L151p User Manual preview
L151p
Brand: ThinkVision Pages: 36
JEA Technologies TPM-193R User Manual preview
TPM-193R
Brand: JEA Technologies Pages: 22
Badger Meter Data Industrial 3100 Series User Manual preview
Data Industrial 3100 Series
Brand: Badger Meter Pages: 32
Postium PRM-102F User Manual preview
PRM-102F
Brand: Postium Pages: 34
Feit Electric FP1X2/6WY/NK Use And Care Manual preview
FP1X2/6WY/NK
Brand: Feit Electric Pages: 7
Tanaka K2-1702 Service Manual preview
K2-1702
Brand: Tanaka Pages: 24
Iiyama ProLite XU2793HS User Manual preview
ProLite XU2793HS
Brand: Iiyama Pages: 39
Polar Electro POLAR M21 User Manual preview
POLAR M21
Brand: Polar Electro Pages: 60
Fujitsu B22W-5 ECO Operating Manual preview
B22W-5 ECO
Brand: Fujitsu Pages: 36
Fujitsu B19-7 LED Operating Manual preview
B19-7 LED
Brand: Fujitsu Pages: 40
Fujitsu B17-5 ECO Operating Manual preview
B17-5 ECO
Brand: Fujitsu Pages: 37
Fujitsu B19W-5 ECO Operating Manual preview
B19W-5 ECO
Brand: Fujitsu Pages: 36
Fujitsu B22T-7 LED proGREEN Operating Manual preview
B22T-7 LED proGREEN
Brand: Fujitsu Pages: 41
Fujitsu B20T-6 Quick Start Manual preview
B20T-6
Brand: Fujitsu Pages: 2
Fujitsu B20T-6 LED Operating Manual preview
B20T-6 LED
Brand: Fujitsu Pages: 40
Asus VP247H User Manual preview
VP247H
Brand: Asus Pages: 29
Asus VP248 Series User Manual preview
VP248 Series
Brand: Asus Pages: 32

Brands by name

Popular brands

Load more brands