IBM P260 Installation And Service Manual Download Page 213 | Manualshive

Page: 213 / 524

background image

BA01D030

Explanation:

DHCP failed to write to the network

Response:

1.

Verify that the network cable is connected, and that the network is active.

2.

If the problem persists: Search RETAIN tips and the firmware change history for the reference code to determine
the recommended actions. If a firmware update is needed, see Updating the firmware

BA01D040

Explanation:

The DHCP discover server timed out

Response:

1.

Verify that the DHCP server has addresses available.

2.

Verify that the DHCP server configuration file is not overly constrained. An over-constrained file might prevent a
server from meeting the configuration requested by the client.

3.

Perform the following actions that checkpoint CA00E174 describes:

a.

Verify that:

v

The bootp server is correctly configured; then retry the operation.

v

The network connections are correct; then retry the operation.

b.

If the problem persists: Search RETAIN tips and the firmware change history for the reference code to
determine the recommended actions. If a firmware update is needed, see Updating the firmware

BA01D050

Explanation:

DHCP::discover no good offer

Response:

DHCP discovery did not receive any DHCP offers from the servers that meet the client requirements.

Verify that the DHCP server configuration file is not overly constrained. An over-constrained file might prevent a
server from meeting the configuration requested by the client.

BA01D051

Explanation:

DHCP::discover DHCP request timed out

Response:

DHCP discovery did receive a DHCP offer from a server that met the client requirements, but the server

did not send the DHCP acknowledgement (DHCP ack) to the client DHCP request.

Another client might have used the address that was served.

Verify that the DHCP server has addresses available.

BA01D052

Explanation:

DHCP::discover: 10 incapable servers were found

Response:

Ten DHCP servers have sent DHCP offers, none of which met the requirements of the client. Check the

compatibility of the configuration that the client is requesting and the server DHCP configuration files.

BA01D030 • BA01D052

Chapter 8. Troubleshooting

201

«
...
211
212
213
214
215
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: NEC Pages: 48

Brand: NEC Pages: 48

CYVMX6800U - 6.8" CLR MONITOR/DVD

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 16

Brand: Panasonic Pages: 28

Brand: Panasonic Pages: 169

Brand: Panasonic Pages: 95

Brand: M-system Pages: 8

Brand: Salutron Pages: 64

Brand: Baaske Medical Pages: 32

Brand: 2E GAMING Pages: 36

Brand: Sigma Pages: 32

Brand: HANNspree Pages: 24

Brand: Inspire Pages: 24

Smart Baby Camera

Brand: Lollipop Pages: 5

DMT80600T104-31WT

Brand: AMP Pages: 14

Brand: Pixio Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands