IBM P260 Installation And Service Manual Download Page 435

Page: 435 / 524

2D14-8157

Explanation:

Temporary controller failure. Replace the system board (SAS controller).

Response:

Failing Item:

FFC_2D14

2D14-9000

Explanation:

Controller detected device error during configuration discovery. Use MAP3190 to determine resolution.

Response:

2D14-9001

Explanation:

Controller detected device error during configuration discovery. Use MAP3190 to determine resolution.

Response:

2D14-9002

Explanation:

Controller detected device error during configuration discovery. Use MAP3190 to determine resolution.

Response:

2D14-9008

Explanation:

Controller does not support function expected for one or more disks. Use MAP3130 to determine

resolution.

Response:

2D14-9010

Explanation:

Cache data associated with attached disks cannot be found. Use MAP3120 to determine resolution.

Response:

2D14-9011

Explanation:

Cache data belongs to disks other than those attached. Use MAP3190 to determine resolution.

Response:

2D14-9020

Explanation:

Two or more disks are missing from a RAID-5 or RAID 6 Disk Array. Use MAP3111 to determine

resolution.

Response:

2D14-8157 • 2D14-9020

Chapter 8. Troubleshooting

423

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands