manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

Failing function codes:

Failing function codes (FFCs) identify a function within the system unit that is failing.

Table 16 describes the component that each function code identifies.

Note:

When replacing a component, perform system verification for the component. See “Using the

diagnostics program” on page 455.

Table 16. Failing function codes

FFC

Description and notes

151

1.

Battery
Note:

After replacing the battery:

a.

Set the time and date.

b.

Set the network IP addresses (for compute nodes that start up from a network).

2.

System-board and chassis assembly

152

System-board and chassis assembly

166

Check the event log for an IBM Flex System Enterprise Chassis blower or fan fault. See the
documentation that comes with the IBM Flex System Enterprise Chassis.

199

System-board and chassis assembly

210

System-board and chassis assembly

212

System-board and chassis assembly (cache problem)

214

System-board and chassis assembly

217

System-board and chassis assembly

219

Common memory logic problem for memory DIMMs.
Note:

If more than one pair of memory DIMMs are reported missing:

1.

Replace the memory DIMM at the physical location code that is reported.

2.

Replace the system board.

221

System-board and chassis assembly

226

System-board and chassis assembly

227

System-board and chassis assembly

241

Ethernet network problem

282

System-board and chassis assembly

292

System-board and chassis assembly (host to PCI bridge problem)

293

System-board and chassis assembly (PCI to PCI bridge problem)

294

System-board and chassis assembly (MPIC interrupt controller problem)

296

PCI device or adapter problem.
Note:

The replacement part can only be identified by the location code reported by diagnostics.

2C4

System-board and chassis assembly

2C7

System-board and chassis assembly (memory controller)

2C8

System-board and chassis assembly

2C9

System-board and chassis assembly

2D2

System-board and chassis assembly (bus arbiter problem)

2D3

System-board and chassis assembly

2D4

System-board and chassis assembly (System/SP interface logic problem)

2D5

System-board and chassis assembly (I2C primary)

446

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

G-Lab MD1500 Instruction Manual preview
MD1500
Brand: G-Lab Pages: 27
Digitensio BP 3BM1-4D Instruction Manual preview
BP 3BM1-4D
Brand: Digitensio Pages: 70
Barco MDRC Series User Manual preview
MDRC Series
Brand: Barco Pages: 55
ViewSonic CD4230 - 42" LCD Flat Panel Display Specifications preview
CD4230 - 42" LCD Flat Panel Display
Brand: ViewSonic Pages: 2
NewHawk UMEN-260314-V1.0 User Manual preview
UMEN-260314-V1.0
Brand: NewHawk Pages: 14
Sanitas SBM 50 Instructions For Use Manual preview
SBM 50
Brand: Sanitas Pages: 80
ALANTIK MOS221 Instructions Manual preview
MOS221
Brand: ALANTIK Pages: 10
Phonocar VM189 Assembling Instructions preview
VM189
Brand: Phonocar Pages: 4
Uniden BW5151R Series Owner'S Manual preview
BW5151R Series
Brand: Uniden Pages: 32
SymCom MOTORSAVER 455-480R Installation Instructions preview
MOTORSAVER 455-480R
Brand: SymCom Pages: 4
TV Logic LEM-150 Operation Manual preview
LEM-150
Brand: TV Logic Pages: 52
Mi RMMNT238NF User Manual preview
RMMNT238NF
Brand: Mi Pages: 11
AOC I2067F Manual preview
I2067F
Brand: AOC Pages: 66
Viotek NBV24CB User Manual preview
NBV24CB
Brand: Viotek Pages: 16
Panasonic TX-1441AE Service Manual preview
TX-1441AE
Brand: Panasonic Pages: 67
Panasonic TY-ST08S Installation Instructions Manual preview
TY-ST08S
Brand: Panasonic Pages: 52
NEC MultiSync E224F User Manual preview
MultiSync E224F
Brand: NEC Pages: 38
NEC MultiSync EA245WMi-2 User Manual preview
MultiSync EA245WMi-2
Brand: NEC Pages: 30

Brands by name

Popular brands

Load more brands