IBM P260 Installation And Service Manual Download Page 423

Page: 423 / 524

2506-3020

Explanation:

Storage subsystem configuration error. Go to Performing the checkout procedure.

Response:

2506-3100

Explanation:

Controller detected device bus interface error. Go to Performing the checkout procedure.

Response:

2506-3109

Explanation:

Controller timed out a device command. Go to Performing the checkout procedure.

Response:

2506-3110

Explanation:

Device bus interface error. Go to Performing the checkout procedure.

Response:

2506-4010

Explanation:

Configuration error, incorrect connection between cascaded enclosures. Go to Performing the checkout

procedure.

Response:

2506-4020

Explanation:

Configuration error, connections exceed IOA design limits. Go to Performing the checkout procedure.

Response:

2506-4030

Explanation:

Configuration error, incorrect multipath connection. Go to Performing the checkout procedure.

Response:

2506-4040

Explanation:

Configuration error, incomplete multipath connection between controller and enclosure detected. Go to

Performing the checkout procedure.

Response:

2506-3020 • 2506-4040

Chapter 8. Troubleshooting

411

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands