IBM P260 Installation And Service Manual Download Page 333

Page: 333 / 524

887-112

Explanation:

External loopback (twisted pair) test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-113

Explanation:

External loopback (twisted pair) parity test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-114

Explanation:

Ethernet loopback (twisted pair) fairness test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-115

Explanation:

External loopback (twisted pair) fairness and parity tests failed. Go to Performing the checkout

procedure.

Response:

Failing Item:

FFC_887

887-116

Explanation:

Twisted pair wrap data failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-112 • 887-116

Chapter 8. Troubleshooting

321

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands