manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

BA140003

Explanation:

The SCSD read/write optical send diagnostic failed; sense data available.

Response:

1.

Troubleshoot the SCSD devices.

2.

Verify that the SCSD cables and devices are properly plugged. Correct any problems that are found.

3.

Replace the SCSD cables and devices.

4.

If the problem persists: Search RETAIN tips and the firmware change history for the reference code to determine
the recommended actions. If a firmware update is needed, see Updating the firmware

BA140004

Explanation:

The SCSD read/write optical send diagnostic failed; devofl command.

Response:

1.

Troubleshoot the SCSD devices.

2.

Verify that the SCSD cables and devices are properly plugged. Correct any problems that are found.

3.

Replace the SCSD cables and devices.

4.

If the problem persists: Search RETAIN tips and the firmware change history for the reference code to determine
the recommended actions. If a firmware update is needed, see Updating the firmware

BA150001

Explanation:

PCI Ethernet BNC/RJ-45 or PCI Ethernet AUI/RJ-45 adapter: internal wrap test failure

Response:

Replace the adapter specified by the location code.

BA151001

Explanation:

10/100 Mbps Ethernet PCI adapter: internal wrap test failure

Response:

Replace the adapter specified by the location code.

BA151002

Explanation:

10/100 Mbps Ethernet card failure

Response:

1.

Reboot the server.

2.

Check for server firmware updates; install the updates if available.

3.

Replace the adapter specified by the location code.

4.

If the problem persists: Search RETAIN tips and the firmware change history for the reference code to determine
the recommended actions. If a firmware update is needed, see Updating the firmware

BA140003 • BA151002

Chapter 8. Troubleshooting

215

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

IBM ThinkVision L191p User Manual preview
ThinkVision L191p
Brand: IBM Pages: 38
IBM E74 Operating Instructions Manual preview
E74
Brand: IBM Pages: 18
Raymarine A Series A50 User'S Reference Manual preview
A Series A50
Brand: Raymarine Pages: 154
Acer CBA272 User Manual preview
CBA272
Brand: Acer Pages: 114
Acer BX320HK Quick Manual preview
BX320HK
Brand: Acer Pages: 4
Interlogix UVM-2600 User Manual preview
UVM-2600
Brand: Interlogix Pages: 84
Garmin SERV Installation Instructions Manual preview
SERV
Brand: Garmin Pages: 8
AOC 203VW+ User Manual preview
203VW+
Brand: AOC Pages: 25
I-Tech iNAP-1700 User Manual preview
iNAP-1700
Brand: I-Tech Pages: 27
Waeco PERFECTVIEW M75LX Installation And Operating Manual preview
PERFECTVIEW M75LX
Brand: Waeco Pages: 248
4D systems gen4-uLCD-43 D Quick Start Manual preview
gen4-uLCD-43 D
Brand: 4D systems Pages: 6
Delta DOP-107 Instruction Sheet preview
DOP-107
Brand: Delta Pages: 2
NEC MultiSync FE772 User Manual preview
MultiSync FE772
Brand: NEC Pages: 44
IBM 6656HG2 - T 560 - 15" LCD Monitor Service Manual preview
6656HG2 - T 560 - 15" LCD Monitor
Brand: IBM Pages: 34
I-Tech UltraView AP-26W User Manual preview
UltraView AP-26W
Brand: I-Tech Pages: 32
ADCMT 6241A Operation Manual preview
6241A
Brand: ADCMT Pages: 306
Hisense Babysense 5s User Manual preview
Babysense 5s
Brand: Hisense Pages: 2
Alienware OptX AW2210 User Manual preview
OptX AW2210
Brand: Alienware Pages: 32

Brands by name

Popular brands

Load more brands