manualshive.com logo in svg

IBM P260, Installation And Service Manual

The Samsung P260 Software Setup Manual is a comprehensive guide that provides step-by-step instructions for setting up and optimizing your device's software. This essential manual can be easily downloaded for free from our website, ensuring you have all the necessary information at your fingertips.

Share
Download
background image

SSSS-138

Explanation:

Error log analysis indicates that the disk drive is operating at a higher than recommended

temperature.

1.

Make sure that:

v

The ventilation holes in the blade server bezel are not blocked.

v

The management-module event log is not reporting any system environmental warnings.

2.

If the problem remains, call IBM support.

Response:

Failing Item:

v

FFC_SSSS

SSSS-140

Explanation:

Error log analysis indicates poor signal quality.

1.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

2.

Replace any parts reported by the diagnostic program.

3.

Replace the system board and chassis assembly, as described in Replacing the system-board and chassis assembly.

Response:

Failing Item:

v

FFC_199

v

FFC_252B

v

FFC_SSSS

SSSS-640

Explanation:

Error log analysis indicates a path error.

1.

Check the BladeCenter management-module event log. If an error was recorded by the system, see POST progress
codes (checkpoints).

2.

Replace any parts reported by the diagnostic program.

3.

Replace the system board and chassis assembly, as described in Replacing the system-board and chassis assembly.

Response:

Failing Item:

v

FFC_SSSS

SSSS-138 • SSSS-640

Chapter 8. Troubleshooting

445

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Elo TouchSystems AMM170TK Operation User'S Manual preview
AMM170TK
Brand: Elo TouchSystems Pages: 37
LC-POWER LC-M44-DFHD-120 Manual preview
LC-M44-DFHD-120
Brand: LC-POWER Pages: 63
Yaesu SM-5000 - COMPUTER Interface Manual preview
SM-5000 - COMPUTER
Brand: Yaesu Pages: 8
Vitek VTM-LCD202 Specifications preview
VTM-LCD202
Brand: Vitek Pages: 2
XP-PEN Artist Pro 16 User Manual preview
Artist Pro 16
Brand: XP-PEN Pages: 12
BenQ FP91GP User Manual preview
FP91GP
Brand: BenQ Pages: 36
Pepperl+Fuchs VisuNet GMP PC219 Hardware Manual preview
VisuNet GMP PC219
Brand: Pepperl+Fuchs Pages: 50
Marshall Electronics V-R72DP User Manual preview
V-R72DP
Brand: Marshall Electronics Pages: 2
OIC Korea VF703GHC Installation And User Manual preview
VF703GHC
Brand: OIC Korea Pages: 12
GoWISE USA GW22059 Instruction Manual preview
GW22059
Brand: GoWISE USA Pages: 18
Sportline SOLO 900 User Manual preview
SOLO 900
Brand: Sportline Pages: 16
Tatung TCM-2102s Specification Sheet preview
TCM-2102s
Brand: Tatung Pages: 2
Rell Healthcare FP1921 rellhealthcare User Manual preview
FP1921 rellhealthcare
Brand: Rell Healthcare Pages: 31
Westinghouse WE28UX8310 User Manual preview
WE28UX8310
Brand: Westinghouse Pages: 31
Safety 1st 08047 User Manual preview
08047
Brand: Safety 1st Pages: 7
Accutrol Apex Premier Installation, Operation & Maintenance Manual preview
Apex Premier
Brand: Accutrol Pages: 61
Faroudja FPP-61HD20 Model Information preview
FPP-61HD20
Brand: Faroudja Pages: 8
Dell P3418HW User Manual preview
P3418HW
Brand: Dell Pages: 64

Brands by name

Popular brands

Load more brands