IBM P260 Installation And Service Manual Download Page 331

Page: 331 / 524

817-217

Explanation:

Time of day clock not running. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_817

887-101

Explanation:

POS register test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-102

Explanation:

887I/O register test failed. Go to Performing the checkout procedure.

Response:

887-103

Explanation:

Local RAM test failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-104

Explanation:

Vital Product Data (VPD) failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

887-105

Explanation:

LAN coprocessor internal tests failed. Go to Performing the checkout procedure.

Response:

Failing Item:

FFC_887

817-217 • 887-105

Chapter 8. Troubleshooting

319

Summary of Contents for P260













































































































































































































































































































































































































































































































































Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands

IBM P260, Installation And Service Manual

Search results

Summary of Contents for P260

Reviews:

Related manuals for P260

Brands by name

Popular brands