IBM P260 Installation And Service Manual Download Page 318 | Manualshive

Page: 318 / 524

background image

101-726

Explanation:

The system hung while trying to configure an unknown resource.

1.

Run the stand-alone diagnostics problem determination procedure.

2.

If the problem remains, refer to Failing function codes to find the FFC that matches the last three digits of the
SRN.

3.

Suspect the device adapter or device itself.

Response:

Failing Item:

v

101-888

Explanation:

The system does not IPL. Go to Performing the checkout procedure or undetermined problem

procedure.

Response:

Failing Item:

v

v

103-151

Explanation:

The time-of-day battery failed.

1.

Go to Removing the battery to start the battery replacement procedure.

2.

Go to Installing the battery to complete the procedure.

Response:

Failing Item:

v

109-200

Explanation:

The system crashed while you running it.

1.

Go to Performing the checkout procedure.

2.

If the 8-digit error and location codes were NOT reported, run AIX diagnostics in problem determination
procedure and record and report the 8-digit error and location codes for this SRN.

Response:

101-726 • 109-200

306

Power Systems: IBM Flex System p260 and p460 Compute Nodes Installation and Service Guide

«
...
316
317
318
319
320
...
»

Summary of Contents for P260













































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for P260

Brand: NEC Pages: 72

Weather Monitor II

Brand: DAVIS Pages: 5

Brand: Ebird Pages: 11

Brand: 2E Pages: 32

AFID ADVANCED EASY

Brand: Microlife Pages: 33

Brand: Uniden Pages: 32

Brand: TV One Pages: 12

Brand: e-Ink Pages: 18

SM-5000 - COMPUTER

Brand: Yaesu Pages: 8

Brand: Vitek Pages: 2

Brand: Beurer Pages: 75

Brand: Fisher-Price Pages: 16

Brand: Elo Touch Solutions Pages: 2

Brand: ViSAGE Pages: 58

Brand: UltraView Pages: 36

HeartGuide BO8000-L

Brand: Omron Pages: 72

Brand: Gator Pages: 6

Brand: Velleman Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands